RINA Rules

1. These publications are only available in Italian
2. Bilingual edition (Italian / English)
3. The 1973 edition is still in force for life saving appliances not subject to the provisions of SOLAS 1974/83
4. These publications are only available in English
5. The 1996 edition is still in force for life saving appliances not subject to the provisions of the European Directive 96/98/EC as amended (Marine Equipment Directive)
6. Publications with this note are available, subject to registration in the Marine Member Area at the following link https://membermarine.rina.org/ (registration is free)

SOFTWARE

Leonardo Hull

The product includes:

• Three dimensional FEM analysis Software package for the structural analysis of a ship by means of FEM direct calculations. A dedicated modeller and post-processor with RINA Rules load definition and checks for yielding, buckling, fatigue is included
• Section and bulkhead scantlings Software package to check ship transverse sections and bulkheads, including fatigue and ultimate strength checks of structural details
• Bulk carrier safety An easy tool for the structural assessment of bulk carriers according to the SOLAS and IACS requirements

Leonardo Propulsion

The product includes:

• Shaftline Calculation of torsional vibrations for propulsion or generation plants, including RINA Rule check
• Crankshaft Check of crankshaft according to RINA Rules
• Propeller Software package to check of propeller according to RINA Rules
• Shrink-fit Generalized shrink and force fitting calculations in accordance to RINA Rules

Leonardo Hull 2D - Charter Yachts

The product includes:

• LH2D-CHY a structural check tool for Charter Yachts built in steel or aluminium

Pleasure Craft EC Assessment

The product includes:

• CE-STAB for stability assessment tool - according to ISO 12217-1/2/3

• CE-STAB-I for inclining experiment tool

• CE-STAB-M for meteorological criterion tool

• CE-STAB-S for wind stiffness verification tool
• STR-DIP for structural check tool for hulls in composite material, steel and aluminium alloy
• SCW for small craft windows assessment tool - according to ISO 12216

and the following check lists as well:

• Fire Protection - ISO 9094 - 1

• Fire Protection - ISO 9094 - 2

• Bilge Pumping System - ISO 15083

• Toilet Waste Retention System - ISO 8099

• Permanently Installed Fuel System - ISO 10088

• Liquified Petroleum GAS (LPG) System - ISO 10239

• Man Overboard and Recovery - ISO 15085

Leonardo piping and pressure vessels

The product includes:

• Boiler and pressure vessels - according to RINA Rules

• Hydraulic oil cylinder - according to RINA Rules

REGISTER BOOK

Register Book ⁽⁴⁾

• Available on the web upon registration at https://www.leonardoinfo.com/LibroRegistro
• For further information on how to get our technical software, please contact: staff.communications@rina.org
• For technical issues concerning our software, please contact: technical.software@rina.org or the fax number +39 010 5351542

RULES

Rules for the classification of ships

• REP. 1/E Part A - Classification and Surveys ⁽⁴⁾⁽⁶⁾


• REP. 2/E Part B - Hull and Stability (3 booklets) ⁽⁴⁾⁽⁶⁾
• REP. 3/E Part C - Machinery, Systems and Fire Protection (2 booklets) ⁽⁴⁾⁽⁶⁾
• REP. 4/E Part D - Materials and welding ⁽⁴⁾⁽⁶⁾


• REP. 5/E Part E - Service Notations (3 booklets) ⁽⁴⁾⁽⁶⁾


• REP. 6/E Part F - Additional class notations (2 booklets) ⁽⁴⁾⁽⁶⁾
• REP. 7/E Common Structural Rules for Bulk Carriers and Oil Tankers ⁽⁴⁾⁽⁶⁾

Rules for the classification of naval ships

• REM. 1/E Part A - Classification and Surveys ⁽⁴⁾⁽⁶⁾


• REM. 2/E Part B - Hull and Stability (3 Booklets) ⁽⁴⁾⁽⁶⁾
• REM. 3/E Part C - Machinery, Systems and Fire Protection (2 Booklets) ⁽⁴⁾⁽⁶⁾
• REM. 4/E Part D - Service Notations ⁽⁴⁾⁽⁶⁾


• REM. 5/E Part E - Additionals Class Notations ⁽⁴⁾⁽⁶⁾
• REM. 6/E Rules for the Classification of Existing Naval Ships ⁽⁴⁾⁽⁶⁾
• REM. 7/E Rules for the Certification of Combat System Physical Integration ⁽⁴⁾⁽⁶⁾

Rules for special ships and units

• RES. 1 Rules for the construction and classification of yachts of 5,5 metres international rating class ⁽¹⁾
• RES. 6/E Rules for the classification of pleasure yachts ⁽⁴⁾⁽⁶⁾
• RES. 7/E Rules for the classification of floating docks ⁽⁴⁾⁽⁶⁾
• RES. 8 Rules for the construction and classification of racing sailing boats of 12 metres - 6 metres international rating class ⁽¹⁾
• RES. 13/E Rules for loading and unloading arrangements and for other lifting appliances on board ships ⁽⁶⁾
• RES. 15/E Rules for the classification of underwater units ⁽⁶⁾
• RES. 18 Rules for masting and rigging of sailing ships ⁽²⁾⁽⁶⁾
• RES. 19/E Rules for the classification of inland waterway ships and for conformity to Directive 2006/87/EC ⁽⁴⁾⁽⁶⁾
• RES. 20 Rules for the construction and maintenance of the quality standard of Italian Port Authority Vessels (Corpo delle Capitanerie di Porto) ⁽¹⁾
• RES. 21/E Rules for the classification of High Speed Craft (applicable to craft constructed on or after 1 July 2002) ⁽⁴⁾⁽⁶⁾
• RES. 22/E Rules for the classification of ships with reinforced plastic, aluminium alloy or wooden hull ⁽⁶⁾
• RES. 23/E Rules for the classification of yachts designed for commercial use ⁽⁴⁾⁽⁶⁾
• RES. 24/E Rules for the classification of Fast Patrol Vessels ⁽⁴⁾⁽⁶⁾
• RES. 25/E Rules for the classification of Offshore Units operating in the Caspian Sea and similar areas ⁽⁴⁾⁽⁶⁾
• RES. 26/E Rules for the classification of Offshore Support Vessels ⁽⁴⁾⁽⁶⁾

Rules for the application of governmental rules

• NAS. II Rules for the construction and testing of life saving appliances ⁽³⁾
• NAS. III Pleasure vessels - Collection of RINA rules for the application of governmental regulations ⁽¹⁾
• NAS. 4 Rules for the construction, testing and installation of life saving appliances ^(1)(5)(6)
• NAS. 8 Rules for the issue and maintenance of the Seaworthiness Certificate or the Safety Certificate ⁽¹⁾⁽⁶⁾
• NAS. 9 Rules for the certification of power of diesel propulsion engines of fishing vessels flying the Italian flag ⁽²⁾⁽⁶⁾
• NAS. 10/E Rules for Fire Protection, Detection and Extinction for the Issue and Maintenance of the SOLAS Certificates ⁽⁴⁾⁽⁶⁾
• NAS. 11/E Rules for Fire Protection, Detection and Extinction for the Issue and Maintenance of Statutory Certificates other than SOLAS Certificates ⁽⁴⁾⁽⁶⁾
• NAS. 12 Rules for the issue and maintenance of the Seaworthiness Certificate or the Safety Certificate for fishing vessels having length less than 24m ⁽¹⁾⁽⁶⁾
• NAS. 13/E Rules for fire protection, detection and extinction for the issue of Statutory Certificates for ships with reinforced plastic, aluminium alloy or wooden hull ⁽⁴⁾⁽⁶⁾
• NAS. 14 Rules for the alternative design and arrangements for fire safety ⁽²⁾⁽⁶⁾
• NAS. 15 Rules for the classification of fire reaction of products for the purposes of fire prevention within the framework of the authorization of the Italian Ministry of the Interior ⁽¹⁾⁽⁶⁾
• NAS. 16 Rules for the classification of fire resistance of products for the purposes of fire prevention within the framework of the authorization of the Italian Ministry of the Interior ⁽¹⁾⁽⁶⁾
• NAS. 17/E Rules for the acceptance and certification of ammunition stores on board ship ⁽⁴⁾⁽⁶⁾

GUIDES

• GUI. 2/E Guide for welding ⁽⁴⁾⁽⁶⁾
• GUI. 3 Guide to perform the failure mode and effect analysis (FMEA) for high speed craft (HSC) ⁽²⁾⁽⁶⁾
• GUI. 4 Guide for the ship condition assessment programme (CAP) ⁽²⁾⁽⁶⁾
• GUI. 6 Guide for the selection, application and maintenance of corrosion prevention systems of ships’ ballast tanks ⁽²⁾⁽⁶⁾
• GUI. 8 Guide for the hull structures reassessment of in service ships ⁽²⁾⁽⁶⁾
• GUI. 9/E Guide for the structural design of oil tankers ⁽⁴⁾⁽⁶⁾
• GUI. 10 Guide for the Ship Environmental Rating Assessment - Green Rating (ERA) ⁽²⁾⁽⁶⁾
• GUI. 10 Guida per la valutazione dell’impatto ambientale delle navi - Green Rating (ERA) ⁽²⁾⁽⁶⁾
• GUI. 11/E Guide for the design and operation of Liquefied Natural Gas (LNG) Carriers ⁽⁴⁾⁽⁶⁾
• GUI. 12/E Guide for the Ship Condition Assessment Program (CAP) for bulk carriers ⁽⁴⁾⁽⁶⁾
• GUI. 13/E Guide for the application of the condition based maintenance within the Planned Maintenance Scheme ⁽⁴⁾⁽⁶⁾
• GUI. 14/E Guide for the Yacht Condition Assessment Program (Yacht CAP) ⁽⁴⁾⁽⁶⁾
• GUI. 15/E Guide for risk analyses ⁽⁴⁾⁽⁶⁾
• GUI. 16/E Guide for the Technology Qualification Processes ⁽⁴⁾⁽⁶⁾
• GUI. 17/E Guide on software acceptance in marine application ⁽⁴⁾⁽⁶⁾
• GUI. 18/E Guide for the Ship Condition Assessment Program (CAP) for Pipe Laying Ships ⁽⁴⁾⁽⁶⁾
• GUI. 19/E Guide for approval in principle of novel technologies ⁽⁴⁾⁽⁶⁾
• GUI. 20/E Guide on complete ship model calculation of Passenger Ships ⁽⁴⁾⁽⁶⁾

OTHER PUBLICATIONS

• VAR. 1 IMO Conventions, Codes and Amendments. Items entering into force between 2013 and 2025 ⁽⁴⁾⁽⁶⁾

OFFSHORE

• RES. 11/E Rules for the classification of steel fixed offshore platforms ⁽⁶⁾
• RES. 17/E Rules for the classification of floating offshore units intended at fixed locations and mobile offshore drilling units ⁽⁴⁾⁽⁶⁾
• RES. 25/E Rules for the classification of offshore units operating in the Caspian Sea and similar areas ⁽⁴⁾⁽⁶⁾
• RES. 26/E Rules for the classification of Offshore Support Vessels ⁽⁴⁾⁽⁶⁾
• NC/N. 20 Rules for the design and construction of drilling systems ⁽²⁾⁽⁶⁾

• RC/C. 17E General contract conditions governing system, product and personnel certification ⁽²⁾
• RC/C. 50 Rules for the use of the RINA certification logo ⁽²⁾


• RC/C. 130 RINA Certification general rules - Annex I


• How to submit complaints, observations and appeals

• RC/C. 12 General Rules for the Certification of Services
•  
• RC/C. 134 Rules for the Certification of Contact Centres

• RC/C. 40 General Rules for the certification of management Systems ⁽²⁾

Quality MS

• RC/C. 33 Rules for the certification of Quality Management Systems ⁽²⁾
• RC/C. 34 Rules for the certification of Quality Management Systems in the aerospace sector according to EN9100 scheme ⁽²⁾
• RC/C. 92 Rules for the certification of Quality Management Systems Certification schemes for the automotive sector ⁽²⁾
• RC/C. 94 Rules for the certification of maritime personnel recruitment and placement agencies in compliance with the ILO CONVENTION: Maritime Labour Convention 2006 ⁽²⁾
• RC/C. 133 Rules for the certification of Quality Management Systems in the Medical Devices sector

Environmental MS

• RC/C. 36 Rules for the certification of Environmental Management Systems ⁽²⁾
• RC/C. 44 Guide for validation of the EMAS Environmental Statement ⁽¹⁾
• RC/C. 65 Rules for Ship Recycling Management System Certification ⁽²⁾

Health and safety MS

• RC/C. 37 Rules for the certification of occupational health and safety management systems ⁽²⁾

Infomation technologies

• RC/C. 56 Rules for the certification of Information Security Management System ⁽²⁾
• RC/C. 57 Rules for the certification of Service Management Systems (Information Technology) ⁽²⁾ 
• RC/C. 84 Rules for the certification of Business Continuity Management System ⁽¹⁾

Corporate social responsibility

• RC/C. 05 Rules for the Certification of Social Accountability Management Systems ⁽²⁾
• RC/C. 73 Rules for the certification of Social Accountability Management System according to the “Valore Sociale” Standard  ⁽¹⁾ 
• RC/C. 103 Rules for the Responsible Jewellery Council Certification Program ⁽²⁾

Best 4

• RC/C. 08 Rules for the certification of Integrated Management Systems according to the BEST 4 and Best 4 Plus Scheme ⁽²⁾

Other systems

• RC/C. 04 Rules for the certification of management system to prevent crimes for which corporate administrative responsibility ensues (Italian legislative decree 231/2001) ⁽¹⁾
• RC/C. 27 Rules for the certification of road haulage safety management system according to the Code of Practice ⁽¹⁾
• RC/C. 28 Guide for the certification of a biocontamination control system based on the RABC method ⁽¹⁾
• RC/C. 60 Regolamento per la Certificazione del Sistema di Gestione delle Competenze delle Ditte Appaltatrici di servizi di manutenzione degli organi di sicurezza dei veicoli per i quali Trenitalia è iscritta quale Soggetto Responsabile della Manutenzione nel RIN ⁽¹⁾
• RC/C. 64 Rules for the certification of Security Management Systems ⁽²⁾
• RC/C. 72 Rules for the certification of Energy Management Systems ⁽²⁾
• RC/C. 93 Rules for the certification of event sustainability management systems ⁽²⁾
• RC/C. 97 Rules for certification of asset management systems ⁽²⁾
• RC/C. 104 Rules for the certification of road traffic safety management system ⁽²⁾  
• RC/C. 136 Rules for the certification of mobility management service in compliance with ARVAL Premium Center

• RC/C. 88 Rules for the validation and verification of greenhouse gas assertions ⁽²⁾
• RC/C. 105 Rules for the assessment of the water footprint ⁽²⁾
• RC/C. 107 Rules for the validation and verification of energy efficiency projects ⁽²⁾ 

CE Marking

• NC/C. 57 Rules for the certification of marine equipment in accordance with European Directive 96/98/EC and subsequent amendments ⁽²⁾⁽⁶⁾

• NC/C. 73/E Rules for the EC Type Examination and RINA Type Approval Certification of Fire Extinguishers ⁽⁴⁾⁽⁶)

• RC/C. 15 Rules for the assessment of conformity of pressure equipment according of Directive 2014/68/EU PED

• RC/C. 16 Rules for the issue of Factory Production Control (FPC) certification according to Regulation (EU) no. 305/2011 relating to Construction Products (Annex V point 1.3 - System of assessment and verification of constancy of performance 2+) ⁽²⁾

• RC/C. 19 Rules for the issue of certification of constancy of product performance according to Regulation (EU) no. 305/2011 related to Construction Products (Annex V points 1.1, 1.2, 1.4 - Systems of assessment and verification of constancy of performance 1+, 1, 3) ⁽²⁾

• RC/C. 32 Rules for conformity assessment of machinery according to Directive 2006/42/CE ⁽¹⁾

• RC/C. 68 Rules for the certification of products intended for use in potentially explosive atmospheres in accordance with Directive 2014/34/EU⁽¹⁾
• RC/C. 76 Regolamento per la Valutazione della Conformità di Ascensori secondo la Direttiva 2014/33/UE e DPR 162/99 e s.m.i. ⁽¹⁾
  RC/C. 95 Rules for the certification of personal protective equipment in accordance with European Directive 89/686/EC and subsequent amendments ⁽²⁾⁽⁶⁾
• RC/C. 108 Rules for EC Certification of Recreational Craft and their Components, Personal Watercraft, Noise Emissions from Recreational Craft and Exhaust Emissions from Propulsion Engine ⁽²⁾ 
• RC/C. 122 Rules for Conformity Assessment of Non-Automatic Weighing Instruments in accordance with Directive 2014/31/UE (NAWI)
• RC/C. 127 Rules for the certification of Personal Protective Equipment in accordance with Regulation (EU) 2016/425 ⁽²⁾

Building material

• RC/C. 24 Rules for the issue of certification of the production process control system of concrete production plants ⁽¹⁾

Environmental products

• RC/C. 03 Rules for the validation of the Environmental Product Declaration ⁽²⁾
• RC/C. 79 Rules for the issue of the Certificate of Compliance of the Sustainability of Biofuels and Bioliquids ⁽²⁾ 
• RC/C. 115 Rules for the concession and mantainence of certification of self-declared environmental claims in compliance woth the ISO 14021 standard
• RC/C. 135 Rules for the certification of sustainability of products according to Carla del Mulino

Forest management

• RC/C. 58 Rules for the concession and maintenance of chain of custody certification of forest based products (PEFC - chain of custody) ⁽²⁾
  
• RC/C. 66 Rules for the concession and maintenance of chain of custody certification of products form the forest (FSC - chain of custody) ⁽²⁾

Other products

• RC/C. 07 Rules for Service Certification of professional courses for personnel carrying out activities in the sector of electrical plants and carrying out of the relative examinations ⁽¹⁾
• RC/C. 10 Rules issue of the Certificate of product Conformity and pertinent concession of the Licence to use the Quality Marks ⁽²⁾
• RC/C. 12 Rules for the issue of the Certificate of Service Conformity ⁽²⁾
• RC/C. 63 Rules for the issue of the Certificate of Conformity for hydrographic surveys ⁽¹⁾
• RC/C. 77 Regolamento per la certificazione dei Procedimenti di Saldatura e Brasatura
• RC/C. 106 Regolamento per la certificazione di società che forniscono servizi di efficienza energetica secondo la norma UNI CEI 11352 ⁽¹⁾ 

Marine Products, System and others

• NC/C. 6/E Rules for Checking the Arrangements intended for Sea Transportation of Special Cargoes ⁽⁴⁾⁽⁶⁾
• NC/C. 10 Guide for the type-approval and testing of floating flexible containers ⁽¹⁾
• NC/C. 13 Rules for the type approval and testing of air pipe automatic closing devices⁽²⁾⁽⁶⁾
• NC/C. 18 Rules for the evaluation of a reduced conventional age of ships ⁽²⁾⁽⁶⁾
• NC/C. 20 Rules for type approval of marine plywood ⁽²⁾
• NC/C. 22 Rules for the certification of lifts and escalators for passengers and crew members ⁽²⁾⁽⁶⁾
• NC/C. 23/E Rules for testing and certification of marine materials and equipment ⁽⁴⁾⁽⁶⁾
• NC/C. 24 Rules for the type approval of components of composite materials intended for hull construction ⁽²⁾
• NC/C. 26/E Rules for Safety Management System Certification ⁽⁴⁾⁽⁶⁾
• NC/C. 31 Rules for the type approval, installation and testing of rigid expanded insulating materials ⁽²⁾
• NC/C. 33 Rules for carrying out non-destructive examinations of welding ⁽²⁾⁽⁶⁾
• NC/C. 34 Rules for the type approval and testing of portable flexible hyperbaric chambers ⁽²⁾⁽⁶⁾
• NC/C. 38 Rules for the type approval of flexible hoses and expansion joints ⁽²⁾⁽⁶⁾
• NC/C. 40 Rules for the type approval of portable tanks for pleasure vessels ⁽²⁾⁽⁶⁾
• NC/C. 41 Rules for the type approval of inflatable recreational boats ⁽²⁾⁽⁶⁾
• NC/C. 43 Rules for the certification of service suppliers ⁽²⁾⁽⁶⁾
• NC/C. 47 Rules for the certification of the bollard pull of tugs ⁽²⁾⁽⁶⁾
• NC/C. 48 Rules for the inert gas systems ⁽²⁾
• NC/C. 49 Rules for the Certification of Rated Power of Diesel Propulsion Engines, when this is less than Maximum Continuous Power ⁽²⁾⁽⁶⁾
• NC/C. 57 Rules for the certification of marine equipment in accordance with European Directive 96/98/EC and subsequent amendments ⁽²⁾⁽⁶⁾
• NC/C. 58 Rules for the type approval of mechanical joints for pipes ⁽²⁾⁽⁶⁾
• NC/C. 59 Rules for the certification and acceptance on board of class A and B fire doors ⁽²⁾⁽⁶⁾
• NC/C. 61 Rules for the approval of manufacturers of materials ⁽²⁾⁽⁶⁾
• NC/C. 63/E Rules for shipboard security system certification ⁽⁴⁾⁽⁶⁾
• NC/C. 64/E Rules for testing and certification of materials and equipment for naval ships ⁽⁴⁾⁽⁶⁾
• NC/C. 66/E Rules for the type approval of fixed aerosol fire-extinguishing systems in machinery spaces ⁽⁴⁾⁽⁶⁾
• NC/C. 67 Rules for the type approval of glass reinforced plastic grid platforms ⁽²⁾⁽⁶⁾
• NC/C. 68 Rules for the type approval of products having reaction to fire characteristics in accordance with the IMO FTP Code ⁽²⁾⁽⁶⁾
• NC/C. 69 Rules for the type approval of divisions having resistance to fire characteristics in accordance with the IMO FTP Code ⁽²⁾⁽⁶⁾
• NC/C. 70/E Rules for the certification of innovative environmental technologies (IET) ⁽⁴⁾⁽⁶⁾
• NC/C. 71/E Rules for the Type Approval of Fixed Clean Agent Fire-Extinguishing Systems in Machinery Spaces ⁽⁴⁾⁽⁶⁾
• NC/C. 72/E Rules for the Type Approval of Fixed Powder Fire-Extinguishing Systems in Machinery Space ⁽⁴⁾⁽⁶⁾
• NC/C. 73/E Rules for the EC Type Examination and RINA Type Approval Certification of Fire Extinguishers ⁽⁴⁾⁽⁶⁾
• NC/C. 74 Rules for the Type Approval of Plastic Pipes ⁽²⁾⁽⁶⁾
• NC/C. 75/E Rules for the Certification of Advanced Life Jackets and Buoyancy Aids having Innovative Safety Technology Characteristics ⁽⁴⁾⁽⁶⁾
• NC/C. 76/E Rules for the type approval and periodical controls of liquid foam concentrates used in fixed fire-extinguishing systems ⁽⁴⁾⁽⁶⁾
• NC/C. 77/E Rules for the qualification and certification of marine adhesive bonders for yachts ⁽⁴⁾⁽⁶⁾
• NC/C. 78 Rules for the Qualification and Certification of Coating Inspectors in the Marine Sector ⁽²⁾⁽⁶⁾
• NC/C. 79/E Rules for the type approval of fixed water-based fire-extinguishing systems in machinery spaces ⁽⁴⁾⁽⁶⁾
• NC/C. 80/E Rules for the certification of coating systems ⁽⁴⁾⁽⁶⁾
• NC/C. 81/E Rules for the qualification and certification of technicians and process managers working in factories building yachts and other products made in composite materials having a thermosetting matrix ⁽⁴⁾⁽⁶⁾
• NC/C. 82/E Rules for the certification of the production quality control system of manufacturers of yachts or other products built in composit materials ⁽⁴⁾⁽⁶⁾
• NC/C. 83/E Rules for the Certification of Training and Competency Management ⁽⁴⁾⁽⁶⁾
• NC/C. 85/E Rules for the Certification of Suppliers of Electrical Maintenance Services ⁽⁴⁾⁽⁶⁾
• NC/C. 86/E Rules for the Certification of Sailing Rigs ⁽⁴⁾⁽⁶⁾
• NC/C. 87/E Rules for the Certification of Best Management Scheme of Companies Owning or Managing Passenger Ships ⁽⁴⁾
• NC/C. 88/E Rules for the Certification of Best Management Scheme of Companies Owning or Managing Cargo Ships ⁽⁴⁾
• NC/N. 22 Rules for the evaluation of noise and vibration comfort on board high speed craft ⁽²⁾⁽⁶⁾

• RC/C. 85 General Rules for the Certification of Persons ⁽²⁾

• Specific requirements for the Certification of Persons

NDT personnel

• RC/C. 14 Rules for the Certification of Non-Destructive Test Operators in the Industrial Sector ⁽²⁾
  
• RC/C. 18 Regolamento per la certificazione del personale tecnico addetto alle prove non distruttive nel campo dell'ingegneria civile ⁽¹⁾
• RC/C. 99 Rules for the Certification of Cathodic Protection Personnel

Welders and welding personnel

• RC/C. 20 Rules for the issue of the Certificate of approval of the Centres for the training of Welders of polyethylene pipes ⁽²⁾
  
• RC/C. 21 Rules for the certification of teaching personnel in charge of training welders of polyethylene pipes⁽¹⁾
  
• RC/C. 52 Rules for the certification of Industrial Welders and Welding Operators ⁽²⁾
  
• NC/C. 55 Rules for the certification of Welders of polyethylene pipes and fittings ⁽¹⁾

Certification of operators and companies involved in the use of fluorinated greenhouse gases

• RC/C. 81 Regolamento per la qualificazione degli organismi di valutazione che organizzano le prove d’esame per il personale addetto alle attività di cui ai Regolamenti (CE) n.303/2008, n.304/2008, n.305/2008 e n.306/2008 ⁽¹⁾
• RC/C. 82 Regolamento per la certificazione di imprese che svolgono le attività di cui al Regolamento (CE) n. 304/2008 e al Regolamento di esecuzione (UE) 2015/2067 ⁽¹⁾
• RC/C. 83 Regolamento per la certificazione del servizio di erogazione di corsi di formazione per personale addetto al recupero di determinati gas fluorurati ad effetto serra dagli impianti di condizionamento d’aria dei veicoli a motore in conformità al Regolamento (CE) 307/2008 ⁽¹⁾

Other

Food safety

• RC/C. 01 Guide for the certification of a System for the prevention of hazards based on the HACCP method ⁽²⁾
• RC/C. 119 Rules for the Certification of Food Safety Management Systems ⁽²⁾

Food product certification

• RC/C. 06 Rules for the issue of the Certificate of Conformity for food products and granting of the relative Licence to use the Quality Mark ⁽²⁾

Sustainable fishery

• RC/C. 78 Certification Rules for the MSC standard ⁽²⁾
• RC/C. 86 General Rules for the Certification according to the Friend of the Sea Standard 

Other

• RC/C. 91 Regolamento per la certificazione dei Sistemi di Gestione e/o Prodotto Integrati secondo lo schema “Food Expo Excellence” ⁽¹⁾

• RC/C. 22 Rules for the certification of subsystem for railway interoperability ⁽¹⁾
• RC/C. 23 Rules for the certification of components for railway interoperability ⁽¹⁾
• RC/C. 30 Rules for the certification of Quality Management System according to IRIS standard ⁽²⁾
• RC/C. 31 Rules for certification according to the railway welding standard EN 15085 ⁽¹⁾ 
• RC/C. 71 Rules for the assessment of conformity or suitability for use of railway subsystem, products/applications and components to the safety requirements ⁽¹⁾
• RC/C. 87 Regolamento per la Certificazione dei Soggetti Responsabili della Manutenzione di carri merci ⁽¹⁾

• RC/C. 09 Rules for certification of quality of civil infrastructures ⁽²⁾
• RC/C. 29 Rules for energy certification of buildings ⁽²⁾
• RC/C. 98 Regolamento per il servizio di Diagnosi Energetica ⁽¹⁾

• RC/C. 67 Rules for performing inspections according to the requirements of DPR 462/01 ⁽¹⁾
• RC/C. 69 Rules for the inspection of lifting and drying equipment according to Italian legislative decree 81/08 ⁽¹⁾
• RC/C. 70 Rules for in-service inspection of pressure equipment according to Italian legislative decree 81/08 (and amendments to legislative decree 106/09) and to Ministerial Decree 329/04 ⁽¹⁾
• RC/C. 75 Regolamento per lo svolgimento di attività di ispezione in qualità di Organismo di Ispezione di Tipo A ⁽¹⁾ 
• RC/C. 89 Rules for inspections according to European Union Environmental Technology Verification PilotProgramme (EU ETV) ⁽²⁾ 
• RC/C. 90 Regolamento per lo svolgimento delle attività in qualità di “Organismo di Ispezione di Tipo A” nel settore ferroviario ⁽¹⁾ 
• RC/C. 96 Rules for assessment of the implementation level of ISO 26000 ⁽²⁾